Products

Simplex sprocket, suits 08B chain with 27 teeth. Sprocket fits to a 20mm shaft and secures with grub screws. Identical to part 630-4119

Simplex sprocket, suits 08B chain with 60 teeth. Sprocket fits to a 20mm shaft and secures with grub screws.

24 Tooth Simplex sprocket to suit a 10B Chain. It has been machined out to suit a 60mm shaft. Predominately used on the AD95. Alternate Part No. ...

24 TOOTH SIMPLEX SPROCKET, 5/8" PITCH, 25.4 (1") ID BORE

36T PRIMARY DRIVE SPROCKET primarily used on the JPC2000. This sprocket is driven by a 10B chain.

Fabricated fixed idler sprocket. Suits 08B chain with two 21 tooth sprockets. Sprockets secure with grub screws to a 25.4mm shaft.

These Agrowplow stroke controllers are spring-loaded for easy installation and have nylon rods inserted, designed to protect the cylinder rods from...

These Agrowplow stroke controllers are spring-loaded for easy installation and have nylon rods inserted, designed to protect the cylinder rods from...

Tapered Roller Bearing suits AP81 and AP91 wheel assemblies. Used on the 10-stud KHitch hub assembly. There are two bearings utilized per hub.

10STUD HUB CAP, suits AP81 and AP91 machines. HUB CAP ONLY. This is used in tandem with an O-ring to seal the 10 Stud K-Hitch hub.

CROWN NUT, suits AP81 and AP91 machines. CROWN NUT ONLY

Machined hub part to suit 10 stud axle assembly on AP81, AP91 and AP92 machines. This hub is used in conjunction with these parts:  1 x HUB CAP    ...

Dust cap or Hub cap to suit the 50 series hub used on the AD130.

6 x 205 PCD HUB and STUB assembly. Suits the AD230 and AP51 Alt Part Number: SKU 139-2032

This dust cap suits the AD230 and AD240 stub axles. It has three mounting holes with a grease nipple in the centre. Also known as a dust cover or a...

6 x 205 PCD HUB and STUB assembly. SUITS THE AD240

Sweeps are designed for the #9 and #8 shank assemblies and can fit to any shank with 22mm 1/2" holes. Sweeps increase the shanks effect on the grou...

This bearing spacer is utilised on the #9 Hydraulic Swing arm and has been designed to fit through a 40mm bearing. There are 2 spacers utilised per...

Tee-bolt used on the #7, #8 spring jump, and #Econo Shank Assemblies. The tee-bolt runs through the centre of the spring to secure it to the assemb...

Tension spring used in the current AD140 drive assembly. It is made out of 6.3mm Wire Gal, has an OD of 59mm and has around 28 total coils. This s...

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-485

Chain tensioner made in engineering plastic, outer diameter 30mm, 55mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 30mm, 75mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 40mm, 105mm long.

Chain tensioner made in engineering plastic, outer diameter 40mm, 135mm long.

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Equivalent Part No. 124-4085

Chain tensioner made in engineering plastic, outer diameter 50mm, 40mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-484

Chain tensioner made in engineering plastic, outer diameter 50mm, 80mm long.

Nylon chain tensioner cut from 70mm rod. Used on seed drill assemblies including the 13 and 18 run Agrowpdrills and the 3000 and 3400 seed drill mo...

(x2) offsets are required to update an AD230. This is intended to shift the front tynes forward by 150mm in the case that the tyne is fitted with d...

Top cylinder pin commonly used on the 3000 series Agrowdrill. It is made out of a 25.4mm bright shaft, is 250mm long and comes with two holes drill...