Agrowplow

Shank Carrier for the 120-0015 #1 Rigid Shank Assembly (Pre 1982) *Old Part No. 002-102

Shank carrier for old model #1 hydraulic shank assemblies. This part is not suitable for all #1 shank assemblies; please refer to your parts manu...

Shank Carrier for the #8 Hydraulic Shank Assemblies. Can also be used in the #1 Hydraulic Shank Assembly to replace the carrier 005-2004. This ena...

Shank Carrier for the #8 Rigid Shank Assembly 100x100mm (120-0006) *Old Part No. 002-101

Used in the Rigid Econo Shank assembly 008-1000

Shinguard to suit 24 and 30" #8 Shank. Available with additional hardfacing to reduce wear and extend the working life of the shinguard.  Old Part ...

Full-length shank shinguard to suit the #9 shank assemblies or the #8 hybrid assemblies. The #9 shinguard provides protection up the full face of t...

Full-length shank shinguard to suit the #9 shank assemblies or the #8 hybrid assemblies. The #9 shinguard provides protection up the full face of t...

Shinguard to suit the Econo style shanks.  Old Part Number: 121-302

Fits the Heavy Duty No8. Spring Jump Assembly 120-005. L660 x W90 x H8

Fits #8 and #1 Hydraulic Assemblies *Old Part No. 107-353

Side plate to suit the Econo Spring Jump Assembly 120-0020 Old Part No. 001-304

Suits the #8 and #1 Hydraulic Shank Assembly

SHANK ASSEMBLY #8 SPRING JUMP SPACER PLATE H.D.S.J. SPACER PLATE (DOGBONE)

Used in the 120-0020 UTILITY SPRING JUMP ASSY also known as the SHANK ASSEMBLY #Econo SPRING JUMP 100x100.

Heavy Duty Coil Spring used as part of the #7 Spring Jump and #8 Spring Jump assembly. Old Part No. 124-013

Clamp plate used as part of the #7 Spring Jump and #8 Spring Jump assembly mountings. Old Part No.003-302107-002

Clamp plate used as part of the #7 Spring Jump and #8 Spring Jump assembly mountings. Old Part No.003-302107-002

Metal spacer used to space out sprockets by 30mm. Designed to fit onto a 50mm shaft. Alternate Part No.117-411

24 TOOTH SIMPLEX SPROCKET, 5/8" PITCH, 25.4 (1") ID BORE

Tapered Roller Bearing suits AP81 and AP91 wheel assemblies. Used on the 10-stud KHitch hub assembly. There are two bearings utilized per hub.

CROWN NUT, suits AP81 and AP91 machines. CROWN NUT ONLY

Machined hub part to suit 10 stud axle assembly on AP81, AP91 and AP92 machines. This hub is used in conjunction with these parts:  1 x HUB CAP    ...

Sweeps are designed for the #9 and #8 shank assemblies and can fit to any shank with 22mm 1/2" holes. Sweeps increase the shanks effect on the grou...

This bearing spacer is utilised on the #9 Hydraulic Swing arm and has been designed to fit through a 40mm bearing. There are 2 spacers utilised per...

Tee-bolt used on the #7, #8 spring jump, and #Econo Shank Assemblies. The tee-bolt runs through the centre of the spring to secure it to the assemb...

Chain tensioner made in engineering plastic, outer diameter 50mm, 80mm long.

M20 U-Bolt to secure to 150x200 RHS.

U-Clamp mounts the shank assembly onto the RHS frame. Suits the 150x150mm (020-1005) #8 Rigid Shank Assembly. Old Part No: 020-205

U-Clamp mounts the shank assembly onto the RHS frame. Suits the 178x178mm (020-1000) #8 Rigid Shank Assembly. Old Part No: 020-206

V bolt secures to 100x100 RHS with M16 hardware.

Part of the 'Shark Tooth' assemblies 111-2020 and 111-2022. This component sets the depth of the #8 shank in the assembly. *Old Part No. 111-324

This stainless steel helical spring lock washer (metric series) is used in tandem with a Posi Pan Screw to fasten the Plastic Roller Bearing Assemb...

Convert, repair or upgrade to the #8 Style Shank. Don't go through the expense of buying a completely new set of #8 assemblies. Simply cut the base...